|
|
|
| | MXG is the new AiM dashlogger designed to acquire and display data coming from your ECU, the internal accelerometer and gyro, as well as from the GPS08 Module included in the kit, analog/digital inputs and predefined math channels.
Performance and data acquired can also be incremented adding up to eight expansion modules.
Its 7" display makes it perfect for wide cockpits installation. | | | | | | | | | | | | ECU
connection | | Analog/digital
inputs | | GPS08 Module | | Second
CAN |
| | | | | | | | | | Internal
accelerometer
and gyro | | Math
channels | | | | |
| |
|
|
|
| | | With the CAN Output you can send messages directly to an existing CAN network in order to improve the range of vehicle control possibilities. |
|
|
|
| | A high contrast TFT display identifies MXG at the first glance.
An ambient light sensor keeps the backlight at optimum brightness levels. | |  | |
|
|
|
| | You can define all the custom pages you wish, choosing among a wide library of page styles, defining which data to be shown, their end of scale and measure units.
Swapping between pages can be managed pushing one or two pushbuttons. | |  | |
|
|
|
| | MXG features eight configurable RGB alarm LEDs: you choose the conditions, you choose the colors.
Select a solid alarm or flashing one - and the flashing frequency, choose to have an accompanying text message, and set the alarm priorities. | |  | | Eight configurable RGB alarm LEDs | |
|
|
|
| | MXG features two digital outputs.
Each of them can give an output of 1 amp at 12 volts: they can be configured in order to be turned on/off depending on the value of the analog or digital inputs.
They permit to automatically run external systems, i.e. to switch on/off additional lights, to activate/de-activate a cooling fan or circulation pumps, etc. when a certain event happens. | | | | | |
|
|
|
| | | Choose from a host of advanced multicoloured RGB shift light patterns that can be customized to your liking, and for each unique gear when required. | |  | |
|
|
|
| | | Using the built-in CAN bus, you can add expansion modules to the MXG to increment the performance and the data acquired: | |  | GPS08 Module
Thanks to GPS08 Module (included in the kit) and its Race Studio 3 software, you can immediately get laptimes and all data needed for engine tuning as well as for improving driving technique. |
| |  | Channel Expansion
It permits to add 4 0-5Volt analog channels for pressure, temperature sensors and potentiometers. Two of these channels can be configured to receive digital inputs like wheel speed. |
| |  | TC Hub
It adds 4 K thermocouples. |
| |  | LCU-One Lambda Controller Wide band Lambda controller LCU-One, with Bosch LSU 4.9 probe, providing all Air/Fuel data, lambda value and exhaust gas temperature, allows to perfectly tune the carburetion. |
| | | | | Firmware under development: | |  | Memory Module
Thanks to the SD Card, Memory Module can record all your data in a file that can be downloaded on your PC for post-analysis. Memory Module, with 16Gb capability, can be connected via CAN-Bus to MXS/MXG and to all AiM loggers. |
| | | | |
|
|
|
| | Race Studio 3 is the heart of your MXG, managing all your activities related to:
Configuration
With Race Studio 3 you can create, modify, delete, import and export configurations with all channels, ECU drivers, Math channels, Display Pages, Digital outputs, Alarms, Shift Lights and all the expansions you need. You will also be able to manage the map of all your racing tracks and compare two laps watching the video recorded by SmartyCam HD cameras. | |  | | Analysis
With Race Studio 3 you can also analyse all data recorded by MXG and downloaded to your PC: graphs, histograms and tables will help you study your performance, providing an objective support to avoid mistakes and improve performances. | |  | | | | AiM LearnFast E-training Series
Check out how to use Race Studio 3 Configuration:
Part 1 - Part 2 | |  | |
|
|
|
| | | Configure, calibrate and download your data wirelessly over a secure 802.11 WiFi connection. | |  | |
|
|
